Pricing
Pricing
Embedded Files
Pricing below is for 1) Full Assemblies ready to ship 2) Sub-Assemblies and 3) components.
Basic stand assembly time without monitors is typically 1 to 2 minutes. Adding your monitors to it should be only another 5 to 10 minutes depending on size and orientations. Some orientations will require screw driver or pliers.
This pricing is geared for those who need 20 units or less or those who want to buy prototypes to test for your needs. Other pricing and business relationships may be available for larger and/or ongoing orders.
Think of us first as a vendor, then as a small fabrication facility, then as a third party purchasing and procurement business, then as a Consultant.
Full Assemblies ready to ship
Full Assemblies ready to ship
We offer a few standard assemblies typically ready to ship in 24-28 hours. You get about a 10-15% discount compared to buying all sub-assemblies or components separate. In general, if you are buying multiple units, if you can buy and cut your own EMT posts you can lower your costs significantly.
We look at these purchases as purchases for life. This is like purchasing universal tools or assets. There is nothing here that should break or get lost, but if it does. the entire system is not lost. These parts can also be repurposed in other configurations as life changes.
For Dual Monitors up to 22" with Telescoping Post - $55 ($63.50 sold separate)
2 monitor plates and hardware with two 4 axis brackets ( $17 x 2 sold separate)
16" telescoping post (16" to 26" adjustable range) ($17.50 sold separate)
Mid duty tubular base with metal 5 way connector, 8" schedule 80 legs, metal 90's for feet and 4 felt pads ($12 sold separate)
The ability to adjust both monitors up and down at the same time after mounting is fairly unique to this system. Most other you would need to adjust them separate. You can, in fact, cut the outer post and add another telescoping connector and adjust separate if preferred. This configuration also allows you to take both monitors off the base while retaining their individual configurations for work and transport. The setup time with this system is greatly reduced compared to many other systems.
For Single Monitors up to 22" with 16" Telescoping Post $35 ($40 sold separate)
1 monitor plate, plate hardware, and 3 axis bracket ($12.50 sold separate)
16" telescoping post ($17.50 sold separate)
Light duty tubular base ($10 sold separate)
The telescoping post is nice to have and it's nice because it can be adjusted from the front while you are sitting down, but if you are going to put your monitor at a single height and leave it, it likely isn't necessary. It is however nice to have if you ever might grow into a 2 monitor system as it does make adjusting those up and down easier.
For single Monitors up to 22" with 16" non Telescoping Post $29 ($33 sold separate)
1 monitor plate and hardware with one 3 axis bracket ( $12.50 sold separate )
16" 3/4 EMT Post (16" post, coupling and cap) ($10.50 sold separate)
Light duty tubular base ($10 sold separate)
Sub Assembly and Component Pricing
Sub Assembly and Component Pricing
Monitor Mounting Plates and Brackets
Monitor Mounting Plates and Brackets
Sub Assembly Pricing
$12.50 - A mounting plate with 3 axis bracket and large ergonomic thumb screw
$17.00 - A mounting plate with 4 axis bracket and large ergonomic thumb screw (you assemble + $2 for assembled)
Component details below...
Monitor Mounting Plate and Hardware
Monitor Mounting Plates - $8
Mounting Plate Hardware - $1.00 per set (10-32 x 3/4" truss head screw, #10 wing nut, small fender washer)
Three Axis Mounting Plate Brackets
These are #0 conduit hangers from the electrical department of your hardware store. These are the square bolt head and nut design, not the speed screws. We do not modify these at all other than to change out the nut if desired.
1 - This is standard as we buy them - $1.50 ea
2 - We change out nut for 1/4" wing nut - $1.50 ea
You should be able to hand tighten for 22" monitors or less, but you may want a wing nut wrench or wrench.
3 - We change out nut for large thumb screw - 3.50 ea
You should be able to hand tighten for 22" monitors or less, but you may want a wrench. ( you will need wrench for the same nut on the 4 axis brackets unless a separate locking arm is used)
4 & 5 - We change out for thumb wheel/screw - 3.00 ea
these are not offset enough from really easy finger use. they work but not ideal without a spacer. Could add oversized nut. We have some to clear out.
4 Axis Mounting Plate Brackets
These are prices for parts only - you assemble (takes 1 to 2 minutes once you get the hang of it. Instructions included or add $2 for assembly) . You will need pliers, wing nut tool, or socket to tighten all of these sufficiently to hold a tilt if you don't use an additional lock attachment.
Parts Only - Assembled - Add $2 if you want them assembled
1 - $6.00 - ( with nut)
2 - $6.00 - ( with wing nut)
3 - $8.00 - ( with large thumb screw)
Parts include:
qty 2 - #0 conduit hangers
qty 2 - spiked external lock washers
qty 1 - precision aluminum spacer
qty 1 - nut / wing nut / thumb screw
qty 1 - m5 x 16 thumb screw (stop screw, not shown)
qty 1 - m5 wing nut
Posts (EMT - others available if interested)
Posts (EMT - others available if interested)
Sub Assembly Pricing
$17.50 - A 16" Telescoping Assembly ( 2 posts, 2 fittings, 2 end caps)
$10.50 - A 16" 3/4" post only ( 1 post, 1 fitting, 1 end cap)
Component details below...
Tube Pricing
1/2 EMT - up to 17" - $5 ea (standard stock is 12" and 16" )
1/2 EMT - 17" to 30" - $6 ea (shipping costs are higher)
3/4 EMT - up to 17" - $6 ea (standard stock is 12" and 16" )
3/4 EMT - 17" to 30" - $7 ea (shipping costs are higher)
Connector and End Plug Pricing
3/4 EMT Coupling Customized for Telescoping - $4 ea
1 std screw and drilled and tapped for/with m6 thumb screw
1/2" EMT End Connector - $1.50 (not modified)
1/2" and 3/4" plugs $0.50 each
Bases - Tubular
Bases - Tubular
For 1 or 2 monitors up to 22" using the 4 axis brackets - $12
1x 1/2" x 5 way metal connector, 2 x 8" schedule 80 pvc threaded nipples, 2 x 1/2 elbows, 4 felt feet)
For 1 monitor up to 22" using the 3 axis bracket - tbd ( $10)
Page updated
Report abuse